Note that when used with SM2256AB chip, it’s not required to initialize SPI EEPROM (via MP tool setting).Ģ. Support of Samsung 19nm TLC, Toshiba A19nm TLC, and Hynix 16nm TLC.ĥ. Improvement of timeout issue of WHCK test.Ĥ. Enable UART interrupt to dump error/event log when FW hang up.Ģ. Bug fix of read retry flow on Samsung 19nm 128Gb TLC.ĥ. Enable Flash support of Samsung 16nm 128Gb TLC.Ĥ. Fixes of CDM and ATTO test FW hang up issues.Ĥ. Fix of EOB fail handling in rebuild link flow.ġ. Fixes of SMART issues for erase count and temperature.ĥ. Enable support of manufacturing burn-in test (RDT) for production.Ĥ.
MPTOOL EEPROM DOWNLOAD
Fix of the issue of download ISP for Hynix 16nm 128Gb TLC.ģ. Fix of the issue that Slumber current is higher than Partial.Ģ. Fix the issue of FW hang up when doing SPOR test.ġ. Add the mechanism to avoid read ECC fail of next time.ĥ. Fix the issue that SLC spare block is risky to run out.Ĥ. Fix the issue of changing die command before accessing flash.ģ. Fix the issue of error map handling when doing unsafe power cycle.Ģ. Fixed read retry table fail of Hynix 16nm TLC.ġ. Fixed Microsoft Win10 setup FW hang up issue (FW cannot be activated after being slumber state).Ģ. Add one function to avoid link mismatch for SPOR.ġ. Fixed the issue of mapping table building for SPOR.Ĥ.
Add training window check in drive initializationĢ. Improvement of Vth tracking handling for Hynix TLC (issue found in SMI power cycle test)Ĥ. Bug fix of FW hang up issue in SPOR testģ. Bug fix of incorrect FW handling of UECC in WPRO blockĢ. Improvement of error recovery flow for SPOR and S4 test.ġ.
MPTOOL EEPROM UPDATE
Update timing parameters of DRAM to accommodate PCB marginality.Ģ. Enable feature of identifying specific CH/CE failure during drive initialization.ġ. Bug fixes of rarely hit issues, 4K alignment in Extra Read, Multiple-CH Read in spare read link, read runtime Info in Pretest, and DMC issue after COMRST.Ģ. – Add delay time before Read Status Command to avoid some timing issue in Pretest flow.ġ. – Bug fix of check for SLC cache size along with bad blocks in system region – Enhancement of SATA error handling and compatibility. – Enhance NAND error handling wit optimized read retry before LDPC soft decode. – Bug fix of RDT/BI result for 960GB (1CE/2LUNs). – Improvement of SATA error handling for DMA command. – Optimize LDPC soft decoding and Vth tracking flow (especially for Hynix TLC). – Improvement of Vth and LDPC tracking for Hynix 16/14nm TLC. – Bug fix of Read Retry for Hynix 14nm TLC – Minor fixes for ULINK and host compatibility issues. – Improve DQS handling for Hynix 16nm TLC. – Update TCL retry flow of Samsung 16nm TLC.
MPTOOL EEPROM PORTABLE
MPtool software is portable software so you can run the software from external hard disk, flash drive or from your computer.
MPTOOL EEPROM FREE
MPTool program also called Canon MP service program, this program is free for personal use and the software is easy to use and no installation is required. It is possible MPTool software is now is the only software resetter for canon Pixma MP in the world. This software works well on following canon printer models: MP150, MP160, MP170, MP180, MP450, MP460. The MPTool program is designed to work with Canon MP-Series.
0 kommentar(er)
